General

 

Due to the horizontal pusher system, the highest possible operational security is guaranteed. So that the load can be pushed off with the lowest possible friction values, the agroliner pusher trailer has a stainless steel base as standard and the pusher plate is coated with VA sheet steel plates. The side panels are designed to be torsion-resistant so that the seal, particularly with bulk cargo such as rapeseed and grain, is guaranteed to be long-lasting. The standard large volume tailgate effectively increases the loading volume.

Technical data

Load capacity

Permissible total weight: 31,000 - 34,000kg *
Empty weight: approx. 9,980kg (in the basic version)
Payload: approx. 21,020kg
Drawbar load: 4,000kg bis 40km/h (2,000kg over 40km/h)
Load volume: approx. 45 - 51.5m³ *

Dimensions

Internal cargo area dimensions: approx. 9,200mm L x 2,370mm W x 2,020mm H

Technical details

Oil requirement: approx. 44 litres *

 *= depending on equipment

Basic version

The basic version of the TAW 30 offers a solid foundation for many purposes with an attractive price/performance ratio. Included in the basic version are:

Add to your wish list Add to your wish list

Tyres 6 x 425/65 R22.5 factory refurbished tyres on centre well rims, approved for 80 km/h
Axles ADR axles 3 x 12 tonnes (60 km/h), 2,150 mm track width (technical 105 km/h) wheel brake 420 x 180 mm, 150 mm square axle
Springs 36 tonnes parabolically suspended linked steering unit with dynamic brake compensation, 1525 mm axle wheelbase
Steering 3rd axle carried out as self-steering axle, hydraulic lock
Draw gear rigid towing device with Scharmüller round shaft drawbar head Type K80, 4 tonnes drawbar load up to 40 km/h (2 tonnes when more than 40 km/h), mechanical saddle landing gear with rapid speed
Chassis frame welded construction, main load bearer made from weight-optimised I beams
Brake system dual line service brake system with automatic load-dependent brake force control (ALB), 6 x diaphragm brake cylinder, spindle parking brake acting on 1 axle
Hydraulic system the tractor must be equipped with 3 double-acting controllers: 1 x connection for the sliding device (advance and retract) and 1 x hydraulic tailgate as well as 1 x single-acting for the self-steering axle
Pusher plate rail-guided push plate with 3 double-acting hydraulic cylinders, cover plate from 2.5 mm stainless steel with sturdy replaceable PU seals, viewing window in the pusher plate approx. 800 x 480 mm, mechanically foldable bulkhead, carried out as grille
Cargo area two-piece floor assembly (movable element at the front, fixed element at the rear), cover plates comprising of 2.5 mm stainless steel with 2 mm profile metal sheet base, 3 mm side panels made from high-tensile fine grain sheet steel plate in welded ribbed construction, the floor assembly is screwed on, hydraulic large area tailgate with surrounding replaceable rubber seal, hydraulic 4-fold locking mechanism, prepared for grain sliders
Electrics 12 Volt system according to the guidelines of the StVZO (German traffic laws) with 7-pin connecting cable, triangular reflector and yellow side reflectors, 3 chamber lamps (rubber mounted), number plate lighting, position lights
Accessories stable foldable underride protection made from round tube, 2 x wheel chocks with bracket, plastic mudguard at the rear, hose cabinet for all supply lines on the drawbar
Paintwork Vehicle sprayed, dressed, degreased and additionally phosphated, cathodic dip painted (CDP), covering coat of the chassis using powder coating, top coat of the side panels and tailgate in German quality dual-component gloss paint. Assembly: Kröger green; Chassis: Kröger red
Additional equipment

To prepare the TAW 30 in the best way for special tasks, we offer a wide range of options:

(You can add the individual items of optional equipment to the wish list using the + symbol.)

  SUPERSTRUCTURE
Add to your wish list A 180B1 Pluggable side panel extensions (aluminium) 300 mm for side panels up to approx. 1000 mm before the end of the superstructure (increases the loading volume by approx. 6 m³)
Add to your wish list A 185B1 Hydraulically lifted mulching flap 500 mm high (instead of the mechanical version)
Add to your wish list A 190B1 Pluggable side panel extensions (aluminium) 300 mm for large area tailgate
Add to your wish list A 270B1 Mobile aluminium stepladder with brackets
Add to your wish list A 280B1 Additional viewing window with guard screen in the bulkhead
Add to your wish list A 543B1 Top mechanically foldable side panels 500 mm (one-side only, right or left side) for reducing the overhead loading height, mechanical locking
Add to your wish list A 570B Grain hatch without chute in the middle in the tailgate (480 x 290 mm)
Add to your wish list A 650B Platform with accident protection bar on the bulkhead including aluminium stepladder
Add to your wish list A 700B1 Yellow tarpaulin with aluminium roller pipe, plug-in triangles and fastening material (only in combination with A 650B / can only be used without attachment)
Add to your wish list A 750B1 2-wing hydraulic cargo area cover system driven by oil motors, covered with a net (e.g. for manure / silage / double-acting control unit and 3-pin 12-V socket required / not compatible with extension)
  CHASSIS
Add to your wish list F 055B1 6/2-directional valve for 2 double-acting functions; switching point on a double-acting control unit
Add to your wish list F 130B1 Towing device at the rear
Add to your wish list F 180B1 Plastic mudguard, front axle (required for warning panel packet)
Add to your wish list F 200B1 Tarpaulin cover at the rear over the entire width of the vehicle from the underride protection to below the loading surface edge
Add to your wish list F 322B1 Reinforced height-adjustable, rubber bearing draw bar, dimensioned for 4 tonnes bearing load (mandatory from 4 tonnes bearing load), version as central tube
Add to your wish list F 325B1 Hydraulically suspended draw gear instead of fixed draw gear (only in combination with hydraulic support leg)
Add to your wish list F 329B1 Double hydraulic jack instead of the mechanical landing gear (required for forced steering)
Add to your wish list F 502B1 Double lighting at the rear, thus 2 x three unit lights mounted on the tailgate = standard equipment + 2 x three unit lights mounted on the mudguards of the rear axle
Add to your wish list F 510B1 Side marking lights (LED)
Add to your wish list F 514B1 Contour marking film, yellow on the side and rear of the vehicle (mandatory for approval > 60 km/h)
Add to your wish list F 516B1 Position and number plate lights as LED version
Add to your wish list F 517B1 Warning sign package for wide loads (required from a width of 2,750 mm, only in conjunction with F 180B1)
Add to your wish list F 519B1 3-unit rear lights, round, LED version
Add to your wish list F 521B1 2 x LED reversing lights on the rear of the vehicle (12 Volt 3-pin socket required)
Add to your wish list F 522B1 Separate LED working floodlight on the front wall for improved illumination of the cargo area (12 volt, 3-pin socket required)
Add to your wish list F 527B1 separate switching box with 2 x toggle switches (on+off) for the operation of two electric functions, power supply via 3-pin socket 12 Volt)
Add to your wish list F 529B1 Hydraulic hose marking "Kennfixx" (price per hydraulic pipe)
Add to your wish list F 601B1 Axle wheelbase > 1800 mm for 34 tonnes total weight
Add to your wish list F 621B1 BPW Tridem axle unit 3 x 11 tonnes (max. 60 km/h), hydraulically suspended, including forced steering for the 1st and 3rd axles; 2150 mm track, wheel brake 410 x 180 mm, 150 mm square tube; (only in combination with equipment F 329B1, brake cylinder mounted at top)
Add to your wish list F 673B1 1st axle designed additionally as self-steering axle, brand ADR
Add to your wish list F 720B1 1st axle carried out as lift axle (only possible in combination with hydraulic spring suspension)
Add to your wish list F 902B1 Electronic load control with signal lamp on the vehicle (only possible in combination with hydraulic spring suspension, 12 Volt, 3-pin socket required)
Add to your wish list F 903B1 Signal lamp for the correct closing of the hydraulic tailgate (12 V, 3-pin socket required)
Add to your wish list F 926B1 Central lubrication system BEKA-MAX with 12 Volt electric pump; 1.9 kg grease storage tank; adjustable pump element with overpressure valve for checking the lubricating points - lubricating interval adjustable via a time switch; progressive distributor; designed for up to 65 lubricating points
Add to your wish list F 930B1 Tie rods, forced steering (2x) with additional automatic telescope
Add to your wish list F 956B1 Press valve to press light bulk goods, switched electrically, manually controlled, continuously adjustable from the tractor unit (approx. 50 to 120 bar), with pressure display
  WHEELS
Add to your wish list R 2635 Tyres, "new" 650 / 55R26.5 BKT FLOTATION RADIAL, profile FL 630, (65 km/h) 169D, (tyre load at 1.5 bar 10 km/h = 5,185 kg)
Add to your wish list R 2645 Tyres "new" 620/60R26.5 NOKIAN Country King (tyre load at 1.5 bar 10 km/h = 5,310 kg)
Add to your wish list R 2765 Tyres, "new" 600 / 55R26.5 BKT FLOTATION RADIAL, profile FL 630, (65 km/h) 165D, (tyre load at 1.5 bar 10 km/h = 4525 kg)
Add to your wish list R 2815 Tyres, "new" 650 / 55R26.5 BKT FLOTATION RADIAL, profile FL 693, (70 km/h) 169D, (tyre load at 1.5 bar 10 km/h = 5,185 kg)
Add to your wish list R 2925 Tyres, "new" 710/50R26.5 BKT FLOTATION RADIAL, profile FL 630, (65 km/h) 170D, (tyre load at 1.5 bar 10 km/h = 5.305 kg)
Add to your wish list R 2935 Tyres "new" 710/50R26.5 NOKIAN Country King (tyre load at 1.5 bar 10 km/h = 5,615 kg)
  PAINTWORK
Add to your wish list L 100B1 Special paintwork, chassis according to RAL tone
Add to your wish list L 130B1 Special paintwork, superstructure, according to RAL tone
  EXPERT'S REPORT/HANDING OVER
Add to your wish list T 150B Expert's report for 40 km/h registration
Add to your wish list T 200B Expert's report for 60 km/h registration (max. 2 tonnes bearing load permitted)
Add to your wish list T 500B1 Technical instruction on-site
Add to your wish list T 900B1 Transport costs, German post code 0-4
Add to your wish list T 910B1 Transport costs, German post code 5-9
Practical examples

Over recent years, we have adapted the TAW 30 to meet the customer's wishes for many tasks. One of our particular strengths: you only pay for what you really need!

Pusher trailer with grass mulch

Practical examples: Pusher trailer with grass mulch

Transporting peat

Practical examples: Transporting peat

When transporting peat, pusher trailers are driven to their limits. Thanks to the stainless steel floor, which allows sliding, and the form-stable side panels, our slider trailer is also able to meet this challenging task too.

Maize harvest required programme

Practical examples: Maize harvest required programme

Experienced drivers use the pusher plate to compact the cargo and thereby significantly increase the transport performance.

Pusher trailer with grass mulch

Practical examples: Pusher trailer with grass mulch

With the pluggable aluminium side panel extensions the total weight can be increased by up to approx 4m³.

Downloads
Download
Standard and ancillary equipment TAW30
2017-10_standard_and_ancillary_equipment_taw30.pdf - 194 kB
Download
Product catalogue Push-off trailer
kr_agroliner_folder_taw_1711_en_web.pdf - 2 MB