SAW 32 - Kröger Nutzfahrzeuge [EN]

Due to the horizontal pusher system, the highest possible operational security is guaranteed. So that the load can be pushed off with the lowest possible friction values, the agroliner pusher trailer has a stainless steel base as standard and the pusher plate is coated with VA sheet steel plates. The side panels are designed to be torsion-resistant so that the seal, particularly with bulk cargo such as rapeseed and grain, is guaranteed to be long-lasting. The standard large volume tailgate effectively increases the loading volume.

Technical data

Load capacity
Permissible total weight:	32,000 kg
Empty weight*:	approx. 8,800 kg (in basic equipment)
Payload*:	approx. 23,200 kg
Fifth-wheel load*:	12.000 kg
Load volume*:	approx. 42 - 51,5m³

Dimensions
Platform height:	1.200 mm (in basic equipment)
Internal cargo area dimensions*:	approx. 9,100 mm L x 2,370 mm W x 2,020 mm H

Technical details
Oil requirement*:	approx. 44 litres

* = depending on equipment.

Basic version

The basic version of the SAW32 offers a solid foundation for many purposes with an attractive price/performance ratio. Included in the basic version are:

Add to notelist

Tyres	4 x 425/65 R22.5 "NEW" on centre well rims approved for 80 km/h
Axles	12 tonnes ADR axles (60 km/h), 2050 mm track width (technically 105 km/h), wheel brake 420 x 180 mm, 150 mm square axle
Springs	24 tonnes parabolically suspended linked steering unit with dynamic brake compensation, 1810 mm axle wheelbase
Kingpin	2-inch
Steering	Rear axle forcibly steered via the fifth wheel, using a mechanical-hydraulic kingpin steering system
Support	2 x mechanical saddle landing gear with rapid speed
Chassis	welded construction, main load bearer made from weight-optimised I beams
Brake system	dual line service brake system with automatic load-dependent brake force control (ALB), 4 x diaphragm brake cylinder, spindle parking brake acting on first axle
Hydraulic system	the tractor must be equipped with three double-acting controllers: 1 x connection for the sliding device (forwards and backwards) and 1 x hydraulic tailgate
Pusher plate	rail-guided push plate with three double-acting hydraulic cylinders, cover plate made of 2.5 mm stainless steel with sturdy replaceable PU seals, viewing window in the pusher plate approx. 800 x 480 mm, mechanically foldable bulkhead, designed as a grille
Cargo area	two-piece floor assembly (movable element at the front, fixed element at the rear), cover plate consisting of 2.5 mm stainless steel, floor plate chassis 3 mm stainless steel with profile plate substructure 3 mm, 3 mm side panels made from high-tensile fine grain sheet steel plate in welded ribbed construction, the floor assembly is screwed on, hydraulic large area tailgate with surrounding replaceable rubber seal, hydraulic 4-fold locking mechanism, prepared for grain sliders
Electrical system:	24-volt system in accordance with the StVZO, with a 15-pin socket, rectangular 5-chamber LED lights, LED license plate light, LED position lights, and yellow side reflectors
Accessories	Hydraulically pivoting, ECE type-approved rear underrun protection, integrated into the sequential control of the tailgate, 2 wheel chocks with holder, plastic fenders on the front and rear axle
Paintwork	Vehicle sprayed, dressed, degreased and additionally phosphated, cathodic dip painted (CDP), top coat of the chassis and tailgate using powder coating, top coat of the side board walls in German quality dual-component gloss paint. Assembly: RAL 9006 white aluminium; Chassis: RAL 7021 black grey

Additional equipment

To prepare the SAW32 in the best way for special tasks, we offer a wide range of options:

(You can add the individual items of optional equipment to the wish list using the + symbol.)

	SUPERSTRUCTURE
	A 106A	Side wall height approximately 2150mm instead of 2020mm (note overall vehicle height)
	A 108A	Side wall height approximately 2300mm instead of 2020mm (note overall vehicle height)
	A 114A	Superstructure length approx. 11,100 mm instead of 9,100 mm, oil requirement approx. 65 litres, tare weight approx. + 2 tonnes, cargo volume approx. 52 m³ according to DIN, without attachment (only in combination with F 270A)
	A 180A	Pluggable side sidewall extensions (aluminium) 300 mm for side board walls up to approx. 1000 mm before the end of the superstructure (increases the loading volume by approx. 6 m³)
	A 185A	hydraulically operated chopper flap 500mm high (instead of mechanical version, dw. Control unit or hydraulic control block F 045A and F 048A required)
	A 190A	Pluggable sidewall extension (aluminium) 300 mm for large area tailgate
	A 270A	Mobile aluminium stepladder with brackets
	A 271A	Holder for broom and shovel mounted on the side of the chassis
	A 280A	Additional viewing window with guard screen in the bulkhead
	A 560A	Shortened tailgate for SAW32/36 approx. 100 mm depth instead of 800 mm (for > 60 km/h registration, a commercial tractor is prescribed)
	A 570A	Grain feed without chute in the middle in the rear board wall (480 x 290 mm)
	A 650A	Catwalk with accident protection bar on the bulkhead including aluminium stepladder
	A 700A	Yellow tarpaulin with aluminium roller pipe, plug-in triangles and fastening material (only in combination with A 650A / can only be used without attachment)
	A 752A	2-wing hydraulic cargo area cover system driven by oil motors, covered with a net (double-acting control unit and 12 volt 3-pin socket required / not compatible with attachments A 180A & A 190A or fold-down side wall)
	A 790A	Galvanised protective cover for rotary actuator of the automatic cargo area cover (only in combination with A 752A)
	CHASSIS
	F 045A	Hydraulic control block for three double-acting functions (pusher plate, tailgate and cargo area cover system incl. remote control (24-volt power supply required via PIN 9 of the 15-pin socket)
	F 020A	Track width 1950mm instead of 2050mm (overall width of 2550mm possible only with a tire width up to 600mm)
	F 048A	Additional double-acting function on the hydraulic control block (20 L/min, not designed for continuous operation, only in conjunction with F 045A)
	F 055A	6/2-directional valve for two double-acting functions; switching point on a double-acting control unit
	F 130A	Towing device at the rear
	F 165A	ECE type-approved underride protection at the rear firmly mounted non-swivelling (for > 60 km/h registration, a commercial tractor is prescribed)
	F 196A	Spray protection in the plastic mudguard (mandatory for approval > 60 km/h)
	F 270A	Side collision protection (not necessary behind an agricultural or forestry tractor)
	F 400A	A.B.S. 24 volt
	F 410A	E.B.S. Electronic brake system (Required for approval of more than 60 km/h and air suspension)
	F 460A	Automatic parking brake (spring-type cylinder)
	F 500A	12-volt lighting system instead of 24 volt with 7-pin socket
	F 505A	Lighting system connection cable 24 V, 15-pin to 15-pin with plugs both ends
	F 506A	Lighting system connection cable 24 V, 15-pin to 2 x 7-pin with plugs both ends
	F 507A	Connection cable ABS/EBS with plugs both ends
	F 510A	Side marking lights (LED)
	F 514A	Contour marking film, yellow on the side and rear of the vehicle (mandatory for approval > 60 km/h)
	F 521A	2 x LED reversing lights on the rear of the vehicle
	F 522A	Separate LED working floodlight on the front wall for improved illumination of the cargo area
	F 523A	2 x LED reversing lights on the side of the chassis
	F 535A	1 inch EDBRO hydraulic couplings instead of standard couplings
	F 621A	Hydraulic spring system including BPW axles (max. 60 km/h), 2150 mm track width, 11 tonnes axle load (at 60 km/h); 410 x 180 mm wheel brake; 150 mm square axle (only in combination with F 460A equipment, brake cylinder mounted at top, double-acting control unit required)
	F 634A	Retrofit kit for ABS and automatic slack adjuster for 12-t axles with 150 mm square axles
	F 705A	Reinforced air suspension without lifting/lowering function for 13 tonnes axle load
	F 715A	Reinforced air suspension with lifting / lowering function for 13to axle load (for registration over 60 km/h only in conjunction with EBS)
	F 900A	Pressure gauge for displaying the bellows pressure mounted on the chassis (only in conjunction with air suspension)
	F 903A	Signal lamp for the correct locking of the hydraulic tailgate
	F 957A	Automatic pre-compaction control for pre-compacting light bulk materials via a sensor on the rear door
	WHEELS
	R 010A	Tyre pressure monitoring (mandatory for registration > 60 km/h with commercial tractor, only in conjunction with F 410A & F 705A or F 715A)
	R 240A	Tyres, "new" 445/65 R22.5 (105 km/h) (fifth-wheel height approx. + 25 mm)
	R 259A	Tyres "new" 560/60R22.5 NOKIAN Country King (65 km/h) 161D with reinforced rims 20.00 (tyre load at 1.5 bar 10 km/h = 5000 kg) (saddle height approx. + 70 mm)
	R 264A	Tyres "new" 620/60 R26.5 NOKIAN Country King, (65 km/h) (tyre load at 1.5 bar 10 km/h = 5,310 kg) (saddle height approx. + 150 mm)
	R 267A	Tyres "new" 600/55 R26.5 NOKIAN CT BAS (65 km/h) 169D, (tyre load at 1.5 bar 10 km/h = 5000 kg) (saddle height approx. + 150 mm, reinforced construction site tyres, not suitable for soft ground)
	R 280A	Tyres "new" 650/55 R26.5 NOKIAN CT BAS (65 km/h) 177D, (tyre load at 1.5 bar 10 km/h = 5220 kg) (saddle height approx. + 150 mm, reinforced construction site tyres, not suitable for soft ground)
	R 347A	Tyres "new" 650/55R26.5 BKT FLOTATION RADIAL, profile FL 695, (65km/h), 178D, STEEL BELTED (tyre load at 1.5 bar 10km/h = 5500 kg, reinforced construction site tyres, not for not suitable for soft ground)
	PAINTWORK
	L 100A	Special paintwork, chassis according to RAL tone
	L 130A	Special paintwork, superstructure, according to RAL tone
	L 140A	Special paintwork for thrust cylinder, bulkhead frame, swivel arm according to RAL tone
	EXPERT'S REPORT/HANDING OVER
	T 150A	Certificate for 40 km/h approval according to EU type approval for vehicle class R (agricultural/forestry tractor), net price not discountable
	T 200A	Certificate for 60 km/h approval according to EU type approval for vehicle class R (agricultural/forestry tractor), net price not discountable
	T 300A	Certificate for 105 km/h approval according to EU type approval for vehicle class R (agricultural/forestry tractor), (net price not discountable, only in conjunction with F 196A, F 400A or F 410A, F 510A, F 514A, F 634A / total external width must not exceed 2550 mm)
	T 300A	Certificate for 105 km/h approval according to EU type approval for vehicle class O (commercial tractor), (net price not discountable, only in conjunction with A 560A, F 165A, F 196A, F 270A, F 400A or F 410A, F 510A, F 514A, F 634A, R 010A / total external width must not exceed 2550 mm)
	T 900A	Transport costs, German post code 0-4 (net price cannot be discounted, transport can only be done per axle)
	T 910A	Transport costs, German post code 5-9 (net price cannot be discounted, transport can only be done per axle)